Antenna 824~960/1920-2170MHz 2dBi cable to U.FL

$1.32
SKU:
AG104
Brand:

Availability:
In stock
Weight:
0.10 LBS
Write a Review

Antenna 824~960/1920-2170MHz 2dBi with cable to U.FL connector

  • Directional antenna concentrates the radiation in one direction, to maximize signal strength.
  • The limited beamwidth reduces "signal noise" / interference from other WiFi networks and third-party wireless devices, resulting in much greater performance of the device connected to this antenna (especially as compared to omni-directional antennas , which pickup 360-degrees of signal noise.

Compatibility with wireless standards & applications :

This directional antenna's range of frequency band compatibility in the 824~960/1920-2170MHz frequency band range, its very low broadband VSWR at 3.0, and impedance matching to 50 Ohm gear , makes it suitable and compliant for all the above applications.

Item

Specifications

Antenna

Frequency Range

824~960/1920-2170MHz

Polarization

Linear

Gain

2dBi

V.S.W.R

< 3.0

Impedance

50Ω

PCB Dimension

40*6.7*1.2mm (1.6 x .30 x .05 in)

Mechanical

Cable

RF1.13

Connector

UFL

Mounting Method

Adhesive

Environmental

Operating Temperature

-40℃~+85℃

Relative Humidity

Up to 95%

Vibration

10 to 55Hz with 1.5mm amplitude 2hours

Environmentally Friendly

ROHS Compliant

ROHS 3 & REACH compliant: Antenna, cable and connector are all compliant with ROHS 3 and REACH.

U.FL Connectors Characteristics and Details:

  • The U.FL female has a socket. U.FL female right-angle type is the most common U.FL connector type found on U.FL cables: 95% of U.FL cables have a U.FL female right-angle connector.
  • U.FL male has a pin and is the connector : Male U.FL is the gender that is the "jack" that is embedded directly on to a circuit board on devices such as BlueTooth boards, and ZigBee radios such as XBee, Printed Circuit Boards (PCBs) and internal mini-PCI wireless cards (even though the gender is male, it is the jack U.FL connector. Hence the male connectors / jacks are very rigid.
  • The small size of U.FL connectors has made them an excellent fit in Machine-To-Machine (M2M) and IOT (Internet of Things) wireless applications, since they take up very little space in the cramped cases of small devices, such as Bluetooth beacons.
  • Gender Determination : Micro-connectors such as U.FL have gender that is counter to typical RF terminology for gender, in that "jack" is more typically synonymous with "female:" A U.FL jack on a board (PCB) is the male U.FL, and the connector that mates with the jack is the female.
  • Connecting and disconnecting U.FL connectors from the jack can be difficult to do properly without damaging the U.FL connector or jack. We offer a U.FL insertion tool to enable you to connect/insert and remove/disconnect easily, without causing any damage to the cable, connector or jack.
  • U.FL connector is also known as Ultra Miniature Coax Connectors (UMCC), and enables attaching an external antenna to a U.FL jack/connector on Printed Circuit Boards (PCBs): U.FL female mates with a female HiRose/U.FL jack, also known as U.FL-LP-66 jack/connector.
  • U.FL Connectors' Material composition
    • Male has a silver-plated phosphor bronze made shell, and a gold-plated brass made contact.
    • Female: The shell and contact of Female U.FL connectors are made of phosphor bronze but are silver, and gold-plated respectively. Female U.FL connectors are the ones used in the termination of antenna cable.
    • U.FL connectors are precision machined. The gold-plating enables low signal loss .

RELATED ANTENNA VERSIONS

 

RELATED PRODUCTS & PAGES:

All of our antennas pass QC test before we ship them.

This antenna is a special order item that will ship in 3-4 weeks from your order

Customer Q&A and Comments

s