Antenna 5dBi 698~6000MHz Ultra Wide Band 5G w/Cable to U.FL


In Stock
0.10 LBS
Write a Review

Antenna 5dBi 698~6000MHz Ultra Wide Band 5G w/Cable to U.FL

698~6000MHz Ultra Wide Band 5GDirectional Patch Antenna with cable to U.FL connector.

Flat low-profile patch antenna, with U.FL connector. Includes a strong adhesive pad so that you can easily mount it in the best position / location for minimal obstruction and optimal signal strength.

  • Directional antenna concentrates the radiation in one direction, to maximize signal strength. Adhesive Mount: Supplied with a 3M strong adhesive base strong adhesive, enabling simple installation. This antenna perfect for quick and simple installations onto surface materials such as metal, glass, wood and plastic.
  • Directional, direct connect antenna tuned to perform on 2.4GHz networks. Linear polarized, it is suitable for many of today’s machine to machine and communication applications such as telemetry, remote monitoring and mesh networking applications.
  • Connector, cable length and type can be customized for large orders.
  • Directional antenna concentrates the radiation in one direction, to maximize signal strength. Screw mount
  • The limited beamwidth reduces "signal noise" / interference from other WiFi networks and third-party wireless devices, resulting in much greater performance of the device connected to this antenna (especially as compared to omni-directional antennas , which pickup 360-degrees of signal noise.

Compatibility with wireless standards & applications :

Suitable and compliant for all the above applications because of this antenna's range of frequency band compatibility in the 2.4 ~ 2.5GHz frequency band range, its low broadband VSWR , and impedance matching to 50 Ohm gear .




Frequency Range





5dBi max


< 2.0



FPC Dimension

120*50*0.2mm (4.7 x 2 x .01 in)



RF1.37 / 5 inch



Mounting Method

Adhesive & Embedded


Operating Temperature



10 to 55Hz with 1.5mm amplitude 2hours

Environmentally Friendly

ROHS Compliant

RoHS 3 and REACH compliant: All of our antenna cables and RF adapters are in compliance regarding content of heavy metals and other toxins that are restricted by RoHS 3 and REACH.

U.FL Connector Characteristics

  • U.FL female has a socket. U.FL male has a pin and is the connector that is the "jack" on a devices such as Bluetooth boards, and ZigBee radios such as XBee, Printed Circuit Boards (PCBs) and internal mini-PCI wireless cards (even though the gender is male, it is the jack U.FL connector.
  • U.FL connectors are widely used in M2M and IOT (Internet of Things) wireless applications.
  • U.FL female right-angle type is the most common U.FL connector type found on U.FL cables: 95% of U.FL cables have a U.FL female right-angle connector.
  • Gender Determination: Micro-connectors such as U.FL have gender that is counter to typical RF terminology for gender, in that "jack" is more typically synonymous with "female:" A U.FL jack on a board (PCB) is the male U.FL, and the connector that mates with the jack is the female.
  • Connecting and disconnecting U.FL connectors from the jack can be difficult to do properly without damaging the U.FL connector or jack. We offer a U.FL insertion tool to enable you to connect/insert and remove/disconnect easily, without causing any damage to the cable, connector or jack.
  • U.FL connector is also known as Ultra Miniature Coax Connectors (UMCC), and enables attaching antenna to a U.FL jack/connector on PCBs: U.FL female mates with a female HiRose/U.FL jack, also known as U.FL-LP-66 jack/connector.
  • U.FL connector is precision machined and gold-plated brass for low signal loss.


All of our antennas pass QC test before we ship them.