Antenna 824~960/1920-2170MHz 2dBi IPEX Connector

$1.32
SKU:
AG104
Brand:

Availability:
In stock
Weight:
0.10 LBS
  • Directional antenna concentrates the radiation in one direction, to maximize signal strength.
  • The limited beamwidth reduces "signal noise" / interference from other WiFi networks and third-party wireless devices, resulting in much greater performance of the device connected to this antenna (especially as compared to omni-directional antennas, which pickup 360-degrees of signal noise.

Compatibility with wireless standards & applications

This directional antenna's range of frequency band compatibility in the 824~960/1920-2170MHz frequency band range, its very low broadband VSWR at 3.0, and impedance matching to 50 Ohm gear, makes it suitable and compliant for all the above applications. 

Item

Specifications

Antenna

Frequency Range

824~960/1920-2170MHz

Polarization

Linear

Gain

2dBi

V.S.W.R

3.0

Impedance

50Ω

PCB Dimension

40*6.7*1.2mm

Mechanical

Cable

RF1.13

Connector

UFL

Mounting Method

Adhesive

Environmental

Operating Temperature

-40℃~+85℃

Relative Humidity

Up to 95%

Vibration

10 to 55Hz with 1.5mm amplitude 2hours

Environmentally Friendly

ROHS Compliant

ROHS 3 & REACH compliant: Antenna, cable and connector are all compliant with ROHS 3 and REACH.

U.FL Connectors Characteristics and Details: 

  • The U.FL female has a socket. U.FL female right-angle type is the most common U.FL connector type found on U.FL cables:  95% of U.FL cables have a U.FL female right-angle connector.
  • U.FL male has a pin and is the connector: Male U.FL is the gender that is the "jack" that is embedded directly on to a circuit board on devices such as BlueTooth boards, and ZigBee radios such as XBee, Printed Circuit Boards (PCBs) and internal mini-PCI wireless cards (even though the gender is male, it is the jack U.FL connector.  Hence the male connectors / jacks are very rigid.
  • The small size of U.FL connectors has made them an excellent fit in Machine-To-Machine (M2M) and IOT (Internet of Things) wireless applications, since they take up very little space in the cramped cases of small devices, such as Bluetooth beacons.
  • Gender Determination: Micro-connectors such as U.FL have gender that is counter to typical RF terminology for gender, in that "jack" is more typically synonymous with "female:" A U.FL jack on a board (PCB) is the male U.FL, and the connector that mates with the jack is the female. 
  • Connecting and disconnecting U.FL connectors from the jack can be difficult to do properly without damaging the U.FL connector or jack. We offer a U.FL insertion tool to enable you to connect/insert and remove/disconnect easily, without causing any damage to the cable, connector or jack.
  • U.FL connector is also known as Ultra Miniature Coax Connectors (UMCC), and enables attaching an external antenna to a U.FL jack/connector on Printed Circuit Boards (PCBs):  U.FL female mates with a female HiRose/U.FL jack, also known as U.FL-LP-66 jack/connector.
  • U.FL Connectors' Material composition
    • Male has a silver-plated phosphor bronze made shell, and a gold-plated brass made contact.
    • Female: The shell and contact of Female U.FL connectors are made of phosphor bronze but are silver, and gold-plated respectively. Female U.FL connectors are the ones used in the termination of antenna cable.
    • U.FL connectors are precision machined.  The gold-plating enables low signal loss.

RELATED PRODUCTS & PAGES:

All of our antennas pass QC test before we ship them.

This antenna is a special order item that will ship in 3-4 weeks from your order

Write a Review